Beta95X Whoop Quad for GoPro Hero 6/7 W/Crossfire RX

Based on theBeta95X whoop platform,we designed aBECboardfor GoPro Hero, which can be used on the Beta95X for video shooting.The wheelbase is only 100mm and weighs about 86.4g without GoPro and battery. With 2.5″ 3-blades propellers, 1106 motors and 16A BLHeli_32 ESC, it could do all the acrobatic motions smoothly, like dive and power loop.We also provide theBeta85X for GoProtoo.

**Note With TBS Crossfire RX.

**Please note that the GoProcamera and the battery are not included!

Bullet Point

• This kit is theoptimal choice for FPV filming,weighs about 85.2g withoutGoPro Hero and battery.
• Install with customized EOS2 V2 camera and A01 VTXyou can enjoy the real-time FPV feds and low RF interference on flight.
• Pad is available for pilot to control the GoPro recording via the radio transmitter.
• Built with the high-performance STM32F051K66 processor FC boards and tunedBETAFPVF405(BEFH),faster input signals with lower latency and higher update rates are reachable, give you much more power.
• Equipped with an adjustable camera mount of 0-50 for FPV film shooting. This will be the best choice for building a smallest cine whoop drone that can carry a naked GoPro6.

Specification

• Item: Beta95X for GoPro Hero
• Weight:85.2g(without GoPro Hero 6 or battery)
• Wheelbase: 100mm
• F405 Flight Controller & 16A BLHeli_32 ESC V2.0
• Frame:Beta95X Frame
• Motors:1106 4500KV with connector
• Props:Gemfan 2540 3-Blades Props
• Receiver Option:TBS Crossfire
• Battery:4S 450mAh Battery(Not including)
• Camera:BetafpvEOS V2 Camera
• Flight time:4min – 5min with 450mAh 4S battery (smooth flight in a windless environment)

95X Cinewhoop with Gopro:

In recent months, more and more pilots are interested in the super small, lightweight, and powerful Cinewhoop. PilotslikeRichrd PappandTommy Tibajiastarted their cinewhoop projectonour Beta85X and Beta95X with GoPro or Insta360 for FPV filming.If you wanna know more about cinewhoop, feel free to join us on Facebook.
>>NAKED Cinewhoop Community

Based on the 95X Whoop platform, we design aBEC boardfor this FPV community which is for the naked GoPro. This whoop drone can carry on the GoPro lite camera and keep in 106g without battery. With a pluggable connector, make iteasier toplug in and out.

Meanwhile, we designed acamera holder forGoPro Lite camera,so you can install the GoPro Lite camera directly and it is also anti-shake. With theadjustable camera mount of 0-50, it can be used for the different flying modes of insane flying or slowing flying.

The idea of GoPro Lite

Based on the discussion of the cinewhoop, we designed a BEC board and a fitting case for Naked GoPro Hero 6/7 to make it as a whole GoPro Lite camera. With a pluggable connector and a lightweightof 29g, easier toinstall on your cinewhoop for FPV filming.

So what is the special of the BEC board? It isintegrated with the 5V@2A BEC, thestock GoPro buttons, LED and remote recording, solving the problem of theunstable power supply andredundant FPC connect way. The current BEC board fits forGoPro Hero 6 and Hero 7 Black.

How to Setup Remote Record

Pilot could use the switch on radio transmitter to start/stop record. Some more configuration needed.

For example, if you useF4 FC V2.0in the drone, like the 95X whoop drone, the connection diagram is shown below.The yellow cable (FCB12 pin pad)is just for the remote record.

We use the Pinio function in Betaflight to control record. First, setup the Pinio function of the B12 pin in the FC board.

resource FLASH_CS 1 NONE
resource PINIO 1 B12
set pinio_box = 40,255,255,255
save

Next,

map one of the switch channels in your radio transmitter to this Pinio (aka USER1). As shown below, we map the AUX4 channel in the radio transmitter to USER1 Pinio.The cursor in the orange zone means button released and white zone means pressed. So keep the cursor in the orange zone in default.

Third, check if the Pinio function works.Change the switch and make the cursor move from the orange zone to the white zone, and finallyback to the orange zone.Now you could check the LED status to know if the record starts. Use the same process to stop recording.

If you use the12A F4 AIO FCboard, like the 85X whoop drone, you will use the LED_STRIP pin (aka A08 pin pad) for the Pinio function.

resource LED_STRIP 1 NONE
resource PINIO 1 A08
set pinio_box = 40,255,255,255
save

Know more about the Betaflight Pinio function.

Package:

• 1 *Beta95X for GoPro Hero
• 1 * BEC Board for GoPro Hero
• 1 * Case for GoPro Lite Camera
• 1 * GH1.25 Power Cable (80mm 30AWG)
• 1 *Pack of Screws

*Please note that the GoProcamera and the battery are not including.